3 December Science 7 Work-Energy-Pulley Systems (Conservation of Energy)

Mindful moment

Past class review–what did you write about the playground swings? what is revealed about force, falling/swinging, energy? Were you surprised at anything that happened or that did not happen? Explain your surprise.

Review today’s blog. Pay close attention to the photographs of the pulley systems.

Prepare your DSN entry.


  • * * * *






3 Dec Pulleys Work-Energy Principle

5 Dec Magnets-Electricity-Electromagnetism-Light-Sound-Wave motion

7 Dec Rube Goldberg Challenge

11 Dec Rube Goldberg Demonstrations and energy writing

13 Dec Magnetism

17 Dec Electricity

19 Dec Sound

How would you explain the idea of Energy? How do you think your idea might compare to the scientific idea? How many forms of energy can you think of? What do you suspect the concept of “work” is? What might be the relationship between work and energy?

  • * * * *

In order to build our ideas about energy, we will examine how forces are applied in pulley systems and how much work goes in and how much comes out. (Energy is the capacity to do work.)

Recall the different relationships between the fundamental quantities: mass, space (distance), time

This is useful <http://hyperphysics.phy-astr.gsu.edu/hbase/work.html>

  • Velocity (speed with direction) = distance/time (Meters/Second)
  • Acceleration = Velocity/time (Meters / Second²)
  • Force = Mass x Acceleration (Kilogram x Meters / Second²) (Newtons)
  • Momentum = Mass x Velocity (Kilogram x Meters / Second)
  • Pressure = Force / Area (Newton / Meter²) (Pascal) (Pounds per square inch-psi; and Bar are units of pressure that are not part of the scientific metric unit system)
  • Work = Force x Distance (Energy is the capacity to do work). (Joules)
  • Power = Work/Time (Force x Distance / Time) (Joules/Second or Watts)

Pulleys are used to make work seem easier.  There are two ways in which a pulley can make work easier.

  1. Pulleys can change the direction of the force
  2. Pulleys can multiply the force applied by spreading it over a longer distance.

There are three main types of pulleys: single – fixed pulley,  single moveable pulley, and   block and tackle – at least one fixed pulley and one moveable pulley in a system.

There are many online references for pulleys. Here is one: http://www.ropebook.com/information/pulley-systems

Build and operate the three systems (see photos). Examine and record the work input and work output of each pulley system and compare them to one another.

PROCEDURE:  Single fixed pulley (see photos)

  1. You will first need to set up a single fixed pulley system as directed by your teacher.
  2. Determine the weight of the object being lifted by attaching it to a Newton spring scale and recording this value in row B.
  3. Attach the weight to one end of a string and run it up and around a single fixed pulley attached to the top bar. Attach the short end of the string to spring scale.
  4. Using a meter stick, note the height at which the spring scale is attached to the string.  Pull on the scale so that it moves at a constant speed and record the reading on the scale in row E.
  5. Move the weight being lifted up .1m (10 cm) from the tabletop to the bottom of the object.  Record this in row C.
  6.  Determine the distance that the scale was moved by subtracting the final reading from the initial reading on the meter stick.  Record this value in row F.
  7. Calculate out the remaining rows using the formulas provided and your data.

Single moveable pulley (see photos)

  1. Tie one end of a string to the top bar.  Run the string through a pulley and attach the other end to a spring scale.
  2. Connect the pulley to the object being lifted and repeat steps 4-8 as you did for the single fixed pulley and record your data in the data table

Block and tackle pulley system (see photos)

  1. Tie a pulley to the top bar.  Loop a string through this pulley.  Tie one end of the string to the top of a second pulley and take the other end and loop it around the second pulley and then tie it to the spring scale.  Connect the weight to the second pulley
  2. Repeat steps 4-8 as you did for the single fixed pulley and record your data in the  data table

Complete the following data table:


Single fixed pulley Single moveable pulley Block and tackle


Resistance force-Weight of object being lifted(N)


Resistance distance -Height that the object is lifted(m)

.1 (10cm)

.1 (10cm)

.1 (10cm)


Work output (J)              = force x distance(B x C)


Effort force (N) (Reading from spring scale as string is pulled)


Effort Distance    How far scale is moved (m)


Work input (J)    = force x distance (E x F)


Mechanical advantage (B/E)


Efficiency = work output/work input(D/G) x 100

1.     Which pulley system required the greatest effort force?  Explain why.

2.     Which type of pulley had the greatest mechanical advantage?  Explain why this is.

(HINT:  Think of which system you had to pull the most string through)

3.     What would be an easier way to determine the mechanical advantage of a pulley system?

(HINT:  Think of how many strings are holding up the weight)

4.     Which pulley system was the most efficient?   Is this what you expected?

5.     Explain the best way that a mechanic could pull out a large truck engine by himself using the least possible amount of force.

6.     Try another system with more than 3 pulleys. Record your ideas and your results.

7.     In what sense does the pulley make the work easier?

8.     Design a simple machine (which works) where the input work is less than the output work. If this is not possible, explain why you think so.

A single pulley. Input force is directed down, weight moves up.

Single moveable pulley. Lifting force moves weight upward.

Block and tackle. One moveable pulley and one fixed pulley.  Downward input force lifts weight upward.

Some different ways to think about energy and energy transformations; the development of ideas about energy:






About rfrazier

AES profile = http://aes.ac.in/viewprofile.php?u=6946
This entry was posted in Science 7. Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *